Wczytuję dane...
Kod producenta: MATEK-F405-STD-OSD
Gwarancja: 12 miesięcy
Wysyłka od: 20.00 PLN
Producent: MATEK

MATEK F405-STD

Kontroler lotu F4

Gyro : MPU6000

Baro : BMP280

Blackbox: MicroSD

BEC 5V - Brak

5x UART

Wymaga znajomości programowania i obsługi kontrolerów lotu.

Polecane oprogramowanie: Beta Flight lub INAV "MATEKF405" od Betafligt 4.1.X "MATEKF405STD (MTKS)"

 

FC Specifications

  • MCU: 168MHz STM32F405RGT6
  • IMU: 32K ICM20602 gyro/accelerometer (SPI)
  • Baro: BMP280 (I2C)
  • OSD: BetaFlight OSD w/ AT7456E chip
  • Blackbox: MicroSD card slot (SD/SDHC)
  • VCP, UART1, UART2, UART3, UART4, UART5
  • Built in inverter for SBUS input (UART2-RX)
  • PPM/UART Shared: UART2-RX
  • SoftSerial on TX2, S5 or S6 optional
  • Camera control on S6 or DAC optional
  • Smartaudio & Tramp VTX protocol supported
  • Battery Voltage Sensor: 1:10
  • Current Sensor: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
  • BEC 5V: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
  • LDO 3.3V: Max.300mA
  • I2C1 SDA & SCL: Yes
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 6x PWM / DShot outputs without conflict
  • 2x 2812LED outputs option
  • 5x UARTs
  • 1x Group of 5V/G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
  • 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
  • 1x pair I2C1 pads
  • 1x Side-press button for BOOT(DFU) mode
  • 1x 16pin bottom mounted FFC Slot for FCHUB-6S, FCHUB-VTX or FCHUB-W connection
  • 36x36mm PCB with 30.5mm mounting holes
  • w/ 2x 0.5mm*16Pin 5cm Flexible Flat Cable
  • w/ 4pcs M3 Anti-vibration Standoffs

TIPS

  • CLI “defaults” after reflashing
  • Rubber anti-vibration standoffs are necessary to avoid the vibration woes.
  • Put a piece of sponge on the barometer to reduce the impact of airflow.
  • If you are using 5V VTX, Pls power the VTX via the 5V pad on FCHUB.  The ribbon cable can’t bear heavy current.
  • BF/  2812LED_Strip share I2C1_SCL pad as default.  either enable LED_Strip, or enable Baro.
  • BF/  2812LED can be resourced to S7 (PB8) if using Baro the same time with BF firmware
  • INAV/  Softserial_TX1 is on TX4 pad & Softserial_TX2 is on TX2 pad if CPU based serial port is enabled since 2.0.1

Tips: Pull out the plastic locking bar carefully so as not to break it.

Betafligh Pins Definition

Pad/Hole PIN TIM Resource option
PPM PA3 TIM5_CH4  
S1 PC6 TIM3_CH1  
S2 PC7 TIM8_CH2  
S3 PC8 TIM8_CH3  
S4 PC9 TIM8_CH4  
S5 PA15 TIM2_CH1 serial_tx 11, camera_control
S6 PA8 TIM1_CH1 serial_tx 11, camera_control
2812 LED Strip PB6 TIM4_CH1  
S7 PB8 TIM4_CH3 LED_STRIP
TX4 PA0 TIM5_CH1 serial_tx 12
RX4 PA1 TIM5_CH2 serial_rx 12
TX2 PA2 TIM9_CH1 serial_tx 11
DAC PA4   no function
  • S5 (PA15) , S6(PA8) or TX2 (PA2) can be resourced to softserial for Frsky SmartPort
  • 2812LED_Strip share I2C1_SCL pad as default.  either enable LED_Strip, or enable Baro.
  • 2812LED can be resourced to S7 (PB8) if using Baro the same time with BF firmware
  • S5 (PA15)  or S6 pad (PA8) can be resourced to Camera Control

CLI command

  • resource motor 5 none
  • resource serial_tx 11 A15
  • resource motor 6 none
  • resource camera_control A08
  • resource motor 7 none
  • resource led_strip 1 B08
  • save

 

INAV Pins Definition

Pad/Hole Pin Inav INav INav INav INav
    Tricopter Quad X Hex X Flying Wing Airplane
PPM/RX2 PA3          
S1 PC6 servo-1 motor-1 motor-1 motor-1 motor-1
S2 PC7 motor-1 motor-2 motor-2 servo-3 servo-3 / Elev
S3 PC8 motor-2 motor-3 motor-3 servo-4 servo-4 / Aile
S4 PC9 motor-3 motor-4 motor-4   servo-5 / Aile
S5 PA15 2812LED 2812LED motor-5 2812LED 2812LED
S6 PA8     motor-6   servo-6 / Rudd
LED PB6 / / / / /
S7 PB8       motor-2 motor-2
SDA/SCL   Mag/Baro Mag/Baro Mag/Baro Mag/Baro Mag/Baro
Klienci, którzy kupili ten produkt wybrali również...