Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli_S 40CH 600mW VTX 700TVL Cam
Znakomity dron wyścigowy o bardzo udanej konstrukcji i znakomitym design, lekka i mocna rama z aluminiowymi oksydowanymi wzmocnieniami. Na pokładzie znajdziemy kontroler lotu F4 z wbudowanym OSD (on screen display - parametry lotu na ekranie FPV), silniki o mocy 496W razem z regulatorem 4w1 BlHeli_S 30A. Model cechuje spory zapas mocy nienaganna konstrukcja oraz wygląd. Kontroler wspiera odbiorniki PPM, DSM i SBUS. Rama wykonana z włókna węglowego i wzmocnieniach z aluminium jest odporna na uderzenia i zapewnia bezpieczeństwo wszystkich elementów.. Wbudowany nadajnik FPV z kamerą wideo i OSD konfigurowalny z BETAFLIGHT zapewnia podgląd parametrów i trybów lotu na ekranie lub goglach FPV.
UWAGA! Do lotu potrzeba zaopatrzyć się w aparaturę i akumulator z ładowarką. Produkty można zakupić w naszym sklepie.
Polecamy aparaturę FLYSKY FS-i6. Dron jest w wersji DIY czyli wymaga złożenia.
Specyfikacja:
Note:
1. This is the DIY version that comes unassembled.
2. Make sure the antenna is installed at the output end before powering up to avoid damaging internal components;
3. Note that the input voltage is within the specified range and is correct and correct to avoid damaging internal components;
4. If the antenna is replaced, select a standing wave and a gain antenna for a longer transmission distance;
5. Pay attention to classic protection during transportation and installation.
6. Take-off weight is about 450g.
1. This is the DIY version that comes unassembled.
2. Make sure the antenna is installed at the output end before powering up to avoid damaging internal components;
3. Note that the input voltage is within the specified range and is correct and correct to avoid damaging internal components;
4. If the antenna is replaced, select a standing wave and a gain antenna for a longer transmission distance;
5. Pay attention to classic protection during transportation and installation.
6. Take-off weight is about 450g.
| Item | Specification |
| 210mm Frame Kit |
Wheel base: 210mm Frame arm thickness: 5mm
Bottom plate thickness: 2mm
Side plate thickness: 2mm
Frame kit material: 3K carbon fiber & 6065 aluminium
|
| 2206 2150KV Brushless Motor |
Motor KV: 2150RPM/V Idle current (Io/10V): 1.26A
Lipo cell: 3-5S
Weight: 31g
Max continuous current: 31A
Max continuous power: 496W
Max thrust: 1050g (4S/5")
Configu-ration: 12N/14P
Motor resistance (RM): 0.0572 Ω
Stator diameter: 22mm
Stator thickness: 6mm
Motor diameter: 27.7mm
Motor body length: 19.2mm
Overall shaft length: 34.2mm
Prop adapter shaft: M5
Bolt holes spacing: 16mm
Bolt thread: M3
Propeller: 5-6 inch
|
| 4 IN 1 30A BLHeli_S ESC |
Continuous current: 30A Burst Current: 40A(10S)
Input voltage: 2-5S
BEC: 5V 2A BEC
Main control chip: 48Mhz EFM8BB2
Firmware: BLHeli_S supports Dshot600
MOS: 5*6 |
| Customized F4 Flight Controller |
Main control chip: STM32F405 Sensor: ICM20602
Power supply: 5V
Integrated OSD
Onboard LC filter
PID cycle rate & gyroscope refresh rate up to 32Khz
Supports BetaFlight / inav racing firmware
|
| 700TVL CMOS Camera |
Case size: 25mm*25mm Weight: 9.5g
Total pixels: PAL: 1020H×596V (0.61MP); NTSC: 1020H×508V (0.52MP)
Effective pixels: PAL: 976H×582V (0.57MP); NTSC: 976H×494V (0.48MP)
Signal system: PAL/NTSC switchable
Resolution ratio(horizontal center): 700TVL
Video output: 1.0Vp-p/75Ω
Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB
White balance: on/off optional
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) - 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: inter-sync
Camera lens: standard 2.8mm
Lens operating voltage: DC12V (wide voltage, measured can work normally at 7.5-13V)
Working current: 70mA (low power consumption)
Working temperature: -20℃~-60℃
Humidity: 0%~98%
|
| 5.8G 40CH 0mW/25mw/200mw/600mw switchable VTX |
Output power & transmission distance: ≥0.5km@25mW, ≥1km@200mW, ≥2km@600mW Transmitting power: 0mW/25mW/200mW/600mW
Full video format: NTSC /PAL
Input voltage & power dissipation: 7V~24V, +12V/260mA@600mW
Size: 20*30*9mm
Weight: ≤7g(except antenna)
With output power self-check function.
Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
|
| Racerstar 5038 2 Blade Propeller |
Material: PC Mounting hole: 5mm
Center thickness: 8mm
Quantity: 10 pairs
Color: blue, red, yellow, purple, white
Weight: 7.25G a pair
Delivery color randomly (10 pairs of propellers are the same color)
|
| Battery | Not included Recommend 3-5S |
Package included:
1 x 210mm frame kit
2 x 2206 2150KV brushless motor CW
2 x 2206 2150KV brushless motor CCW
1 x 4 IN 1 30A BLHeli_S ESC
1 x Customized F4 flight controller
1 x 700TVL CMOS camera
2 x 2206 2150KV brushless motor CW
2 x 2206 2150KV brushless motor CCW
1 x 4 IN 1 30A BLHeli_S ESC
1 x Customized F4 flight controller
1 x 700TVL CMOS camera
1 x 5.8G 40CH 0mw/25mw/200mw/600mw switchable VTX
2 x Battery strap
10 x Racerstar 5038 2 blade propeller CW
10 x Racerstar 5038 2 blade propeller CCW
2 x Battery strap
10 x Racerstar 5038 2 blade propeller CW
10 x Racerstar 5038 2 blade propeller CCW
Polecamy
Dron iFlight Nazgul5 V3 Analog 6s
1590,00
PLN
Dron iFlight Protek25 Analog 4s CineWhoop
1205,00
PLN
Dron iFlight Nazgul Evoque F5D Analog 6s
1690,00
PLN
Dron iFlight Chimera7 Pro V2 6S HD O3
3780,00
PLN
Blade Theory XL FPV BNF Basic
1699,00
PLN
Dron iFlight Protek35 1.2 Analog 4s CineWhoop
1579,00
PLN
Dron iFlight Chimera7 Pro V2 6S LR Analog
2599,00
PLN
Dron iFlight Nazgul Evoque F6X Analog 6s
1799,00
PLN
