Kontroler lotu SpeedyBee F7 V3
MCU: STM32F722
Zasilanie: Lipo 3s-6s
Gyro: BMI270
Blackbox 500M
Baro BMP280
BEC 5V/2A 9V/2A
Bluetooth, Wifi, CameraControl
Waga 10.7g
Wymiary 41 x 38
Specifications
Product Name | SpeedyBee F7 V3 Flight Controller |
MCU | STM32F722 |
IMU(Gyro) | BMI270 |
USB Port Type | Type-C |
Barometer | BMP280 |
OSD Chip | AT7456E chip |
BLE Bluetooth | Supported. Used for Flight Controller configuration |
Flash FC Firmware Wirelessly | Supported. Please enter MENU > FC Firmware Flasher |
Download/Analyze Blackbox | Supported.Please enter MENU > Blackbox Analyzer |
DJI Air Unit Connection Way | Two ways supported: 6-pin connector or direct soldering. |
Flash(for BlackBox) | 500MB |
BetaFlight Camera Control Pad | Yes(CC pad on the front side) |
Power Input | 3S - 6S Lipo |
5V Output | 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A. |
9V Output | 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A. |
3.3V Output | Supported. Designed for 3.3V-input receivers. Up to 500mA current load. |
4.5V Output | Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. |
ESC Signal Pads | M1 - M4 on bottom side and M5-M8 on front side. |
UART | 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6) |
ESC Telemetry UART | R4(UART4) |
I2C | Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. |
LED Pad | Used for WS2812 LED controlled by Betaflight firmware. |
Buzzer | BZ+ and BZ- pad used for 5V Buzzer |
BOOT Button | Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. |
RSSI Input | Supported. Named as RS on the front side. |
SmartPort | Use any TX pad of UART for the SmartPort feature. |
Supported Flight Controller Firmware | BetaFlight(Default), EMUFlight, INAV |
Firmware Target Name | SPEEDYBEEF7V3 |
Mounting | 30.5 x 30.5mm( 4mm hole diameter) |
Dimension | 41(L) x 38(W) x 8.1(H)mm |
Weight | 10.7g |
Uwaga do zdjęć opisu. Przedmiotem oferty jest sam kontroler F7.
Regulator 4 w 1 ESC 50A , moduły dodatkowe GPS , AIR UNIT, odbiorniki radiowe, silniki i inne urządzenia nie stanowią predmiotu oferty,
są one zaznaczone na schemacie w celu ukazania diagramu połączeń.
Polecamy
Matek Analog Pixel OSD module
99,00
PLN
MATEK AP Periph CAN Node L431
99,00
PLN
MATEK H743-MINI V3 Flight Controller
543,00
PLN
MATEK F722-mini SE F7 Flight Controller
364,00
PLN
MATEK H743-SLIM V3 Flight Controller
563,00
PLN
MATEK F411-WTE Flight Controller
280,00
PLN
MATEK H743-WLITE Flight Controller
563,00
PLN
MATEK F405-WMN Flight Controller
443,00
PLN
MATEK F405-TE OSD PDB Flight Controller
376,00
PLN
Matek M10 GPS QMC5883 Compass for FPV
200,00
PLN